混流泵

5、泵運轉時注意有無雜音及泵內是否有劇烈的磨擦和撞擊聲，如有就停車檢查。

When the pump is

running, pls pay more attetion on the noise and friction and clashing noise, if

there are strong noise, pls stop the pump to check.

    6、檢查進、出水管路有無進氣漏氣現象。

Check the

water-in and out pipes if they are leaking air.

    7、如電機與水泵為直聯傳動，需檢查電機與水泵的軸心線是否在同一直線上，以防轉時振動。

When the motor and pump are direct

connected drive ,check the motor and pump axile lead if they are in the same

line to avoid vibrating.

8、水泵在冬季使用時，停車后應將水泵內和管道內的存水放盡以防凍裂。

If use the pump

in winter, pls run off the water from the pump and pipes.

    9、水泵每使用一個灌溉季節后，應更換潤滑黃油后存放。

Replace the

lubricating oil after using the pump for one irrigation season.

10、水泵工作滿500小時，應仔細拆卸檢查零件的磨損情況，如長期停用，應將運轉部分拆下擦干上油妥善保管。

 6、軸承發熱

 The bearing is

 hot

 1、潤滑油脂不足

 2、潤滑油質量不好或不清潔

 3、軸心沒有對準

 4、軸承松動或磨損

 5、皮帶太緊

 1.Lubricating grease is not enough

 2.The quality of lubricating oil is not

 good or dirty

 3.The axes is not aiming

 4.The bearing is loose or attrition

 5.The belt is too tight.

 1、加油

 2、清洗軸承

 3、找正

 4、修正

 5、適當放松

 1.Add lubrication oil

 2.Wash

 the bearing

 3.Aligning

 4.Amending

 5.Loosen it properly

按行業分類石油泵、冶金泵、化工泵、漁業泵、礦業泵、電力泵、水利泵、水處理泵、食品泵、釀造泵、制藥泵、飲料泵、煉油泵、調料泵、造紙泵、紡織泵、印染泵、制陶泵、油漆泵、 、化肥泵、制糖泵、酒精泵、環保泵、制鹽泵、啤酒泵、淀粉泵、供水泵、供暖泵、農用泵、園林泵、水族泵、鍋爐泵、泵、船舶泵、航空泵、汽車泵、消防泵、水泥泵、空調泵、泵、機械泵、燃?xì)獗?、油氣混輸?img src="https://pic.etlong.com/202009/09/081739428618772.jpg" />